DJ-X7T


 

$199.00

In stock
 

The Alinco DJ-X7T wideband receiver covers 100 kHz to 1299.995 MHz (less cellular) in AM, FM wide and FM narrow modes. The illuminated LCD display is large and easy to read. In addition to frequency information, it will also show the operating mode, memory channel. The DJ-X7T can also clone to other DJ-X7 units, sharing its programmed parameters through a wire connection (cable optional).

The DJ-X7T features 1000 memory channels. This radio has four user-selectable antenna choices: an internal AM bar antenna, an internal SW bar antenna, the earphone cable may be used as antenna or the external, supplied SMA whip antenna terminal may be activated.

ALINCO DJ-X7T Features
  • Easy to program memory banks Managing 1000 memories is easy when you use the free software available from the Alinco website and the optional ERW-4C cable (USB/Serial conversion cable usable with ERW-4C for USB connections) to expand your own bank-partitions from standard 10 up to 50! (Note: This feature is accessible only with using the free-software and allows you to freely set up bank partitions up to 50 banks within the available 1000 memory channels.)
  • Pre-set bands make operation easy AM/FM and TV audio bands have been pre-set to make it easy to enjoy the DJ-X7T/E right from the start.
  • Five scan modes Five scan modes are available including preset frequencies, VFO, memory scan, programmed scan or tone scan to search for unknown CTCSS tones. The Timed/busy modes are selectable on all modes except the tone scan mode.
  • Power options keep you in control The DJ-X7 comes with a standard adapter that charges the Lithium ion battery AT THE SAME TIME it powers the radio with AC power. So, you can listen while the unit is charging. Plus, the long-lasting, partially rechargeable lithium ion battery delivers approximately 19 hours of operating time.
    (AC adapter may cause slight noise to the receiving audio on some frequencies. The operating time may vary depending on settings such as audio-volume level, battery-save status etc.)
SPECIFICATIONS
Receiver Range 0.100 - 1299.995MHz continuous
(USA T-version cellular-band blocked 824.000-849.995MHz, 869.000-894.995MHz) 
Mode A3E (AM) / F3E (FM,WFM) 
Antenna Impedance 50 ohms unbalanced / SMA-port
Supply Voltage DC3.7V (external DC port DC3.7V-6.0V)
Current consumption 90mA average/Approx. 65mA stand-by/Approx 22mA battery-save on 
Frequency Stability -7 to +3ppm at +14°F - +140°F
Dimension without projection 58(W) x 96(H) x 14.5(D) mm
Weight Approx.235g / 8.29 oz (Ant.& EBP-74 inclusive)
RECEIVER
Receive circuitry Triple-conv. Super-heterodyne (NFM,AM) / Double-conv. Super-heterodyne (WFM)
1st IF: 243.95MHz
2nd IF: 39.15MHz (NFM,AM) 10.70MHz (WFM)
3rd IF: 450KHz (NFM,AM) 
Sensitivity Typical values in the bands, not the minimum guaranteed values
FM / 30 to 470MHz : 12dBu (0.25uV), 470MHz or higher 6dBu (0.5uV) 12dBSINAD
WFM / 76-470MHz : 2dBu (0.8uV), 470MHz or higher 9dBu (2.8uV) 12dBSINAD
AM / 0.1-50MHz : 0dBu (1.0uV), 50MHz 8dBu (0.4uV) 10dBS/N 
Selectivity 6dB 12kHz or more, 60dB 35kHz or less (NFM,AM), 6dB 130kHz or more, 60dB 300kHz or more (WFM)
Typical Operating Temperature  Approx. 19 hours with EBP58N (RX 1: Stand-by 4 BS-on) 
Audio Output Power Max 100mW or more (8ohms) 
STANDARD ACCESSORIES
  • Instruction manual
  • EBP-58 Li-Ion Battery pack 600mAh
  • EDC-126 AC Adapter 
  • EA133 SMA whip antenna
  • EME-25 Curl-cable earphone 
  • Antenna cap
OPTIONAL ACCESSORIES
  • ESC-38 Softcase 
  • EME-18 Straight-cable earphone 
  • EDH-32 Cigar-socket DC cable 
  • ERW-7 USB PC Interface Data cable
  • ERW-4C PC interface-cable